How a Marshmallow Production Line Runs from Kitchen to Packing

2026/11/16

The Marshmallow Production Line on this page is the automatic marshmallow line from Foshan Aeros Industrial Equipment Co., Ltd. The page says Aeros specially designed an automatic line that produces marshmallow continuously, from the Marshmallow Kitchen to the Aging and De-starch process. It describes the line as a combination of continuous aeration, precise mixing and extrusion to produce fluffy marshmallows with tailored shapes and consistent quality for confectionery factories. The page does not give the capacity, the line length, the power, the air or the steam demand, so a buyer should ask for a layout and a utility list.

The Line Process

The page gives a step-by-step process. In the kitchen, the syrup and the gelatine are prepared; the two ingredients are mixed and cooled until ready for aeration. In aeration, the density is set and the aeration starts, then the foam is supplied to the manifold depositor or the extruder. After depositing, the marshmallow is cut and goes to the aging section; after aging, it moves to de-starch and is ready to pack. A buyer should ask for a process flow diagram and a mass balance for each step.

The page does not give the kitchen tank size, the mixer type or the cooling method. A buyer should ask for the tank, the agitator and the heat exchanger spec. The page does not give a gelatine soak or a syrup Brix control. The buyer should confirm the recipe and the control points. The page does not give a holding time or a temperature. The buyer should ask for the process window for the target recipe. The page does not give a CIP method, so the cleaning plan should be agreed before the order.

Aeration and Mixing Head

The page says the line uses continuous aeration, a well-known technology used in confectionery, pastries and milk products. It says the Aeros mixing head has reached the world standard and that the automation saves labour and reduces energy and material waste. The page does not give an aeration capacity, a density range or a gas type. A buyer should ask for the capacity and the density control range. The page does not give a nitrogen or an air supply. The buyer should confirm the gas source, the pressure and the flow meter.

The page describes the mixing head rotor and stator as precision cut, with no welded needles, made from a complete piece of material, hard enough for viscous products and easy to clean because the surface is smooth. It says the design gives a more even foam size distribution. A buyer should ask for the head material, the gap and the spare parts. The page does not give a head life or a seal kit. The buyer should ask for the wear parts and the service interval. The page does not give a lab or a pilot head, so a trial should be planned.

Capacity and Utilities

The page does not give a production capacity in kg per hour or a line speed. A buyer should send the target output, the product size and the recipe, and ask for a model selection. The page lists aerator models A50, A100L, A200L, A750 and A1000, but it does not map them to a marshmallow capacity. The buyer should ask for the model table and the reference line for a similar product. The page does not give a minimum batch or a changeover time.

The page does not give the power supply, the compressed air, the steam, the chilled water or the floor space. A buyer should ask for the utility schedule and the foundation load. The page does not give a room temperature or a humidity requirement. The buyer should confirm the plant condition for the depositing and the aging room. The page does not give a waste or a rework rate. The buyer should ask for the expected yield and the start-up loss before the acceptance test.

Ordering and Service

The page says Aeros is the main supplier for continuous aeration systems in China and can supply a single unit or a complete turnkey project. It lists installation services and a training and service section with goals such as lower energy consumption, higher productivity and stable production. A buyer should ask for the scope of the turnkey project, the installation team and the training plan. The page does not give a warranty term or a spare parts stock, so both should be written into the contract.

The page does not give a price, a lead time or a payment term. A buyer should send the product, the recipe, the output, the utilities and the plant layout, and ask for a quotation with a process guarantee, a layout, a utility list and an acceptance test. The page has a video link on YouTube for the line. The contact is through the site contact page and the customer message form. For a first order, a pilot trial on the real recipe is the practical way to check the Marshmallow Production Line before a full installation.